Rubber Adaptor (Art.Nr. 60016)

Rubber Adaptor (Art.Nr. 60016)

Price € 4,00

Amount

Moccamaster rubber adapt for between the outletpipe 9 hole and the riser tube into the water tank.


Important note: For the replacement of the adaptor, some experience with electronic devices is recommended. Please read the disclaimer and the instructions!
With the purchase of this article, buyer declares that Technivorm/Moccamaster is not responsible for any damage or personal injuries, caused by repair and/or replacement of parts, conducted by buyer or on his account. If a defect is caused by improper installation of parts, the warranty (if still applicable) is not valid anymore. Buyer waives the right to return for the parts which were sent to repair the machine.

Instructions for the replacement of the rubber adapt

 Important: be careful with the glass tube!

 Tools: Philips screwdriver; T20 Torx screwdriver; tweezers; Soap sud

Disassembly

1.   Put a towel on the table, preferably double

2.   Turn the device upside down and screw the base plate from the machine.

3.   Loosen the black rubber tube from the copper pipe

4.   Look in the device, there is a 'micro switch' where two wires detached onto it. This is the button that is pressed by the jar. Look carefully what thread is attached to what point and make the wires loose with pliers. Be careful not to squeeze the connection.

5.   Loosen the screws in the watertank – put the rubber rings in a safe place, not to lose them. Sometimes they are stuck to the water tank.

6.   Pull the water tank right up from the machine by pulling the tube in the middle. All cables that are attached, come along.

7.   Gently pull off the glass tube, hold the water tank with one hand so it does not "jump" when the tube comes out.

8.   Remove the rubber adapter in which the glass tube is inserted (perhaps use soapy water).

Mounting

1.   Place the new rubber adaptor on the nozzle of the water tank.

2.   Push the glass tube well in the rubber adaptor, the top should come all the way to the top of the rubber adapter, there should be no space in the adapter left. If needed use a hard object (e.g., a book) to press the glass tube in the adaptor but be careful not to break it.

3.   Put this complete set in the machine.

4.   Glass tube gently and straight through the hole in the metal bracket. No bumping or pushing!

5.   Put the screws in the water tank (note the black rubber rings).

6.   Turn the machine and attach the wires to the micro-switch (sliding).

7.   Push the black rubber tube as far as possible on the copper pipe.

8.   Put the screws in the bottom plate.

Did you order the wrong part? You can return unused articles within 14 days after receipt (own expense).

Rubber Adaptor (Art.Nr. 60016)

Moccamaster rubber adapt for between the outletpipe 9 hole and the riser tube into the water tank.


Important note: For the replacement of the adaptor, some experience with electronic devices is recommended. Please read the disclaimer and the instructions!
With the purchase of this article, buyer declares that Technivorm/Moccamaster is not responsible for any damage or personal injuries, caused by repair and/or replacement of parts, conducted by buyer or on his account. If a defect is caused by improper installation of parts, the warranty (if still applicable) is not valid anymore. Buyer waives the right to return for the parts which were sent to repair the machine.

Instructions for the replacement of the rubber adapt

 Important: be careful with the glass tube!

 Tools: Philips screwdriver; T20 Torx screwdriver; tweezers; Soap sud

Disassembly

1.   Put a towel on the table, preferably double

2.   Turn the device upside down and screw the base plate from the machine.

3.   Loosen the black rubber tube from the copper pipe

4.   Look in the device, there is a 'micro switch' where two wires detached onto it. This is the button that is pressed by the jar. Look carefully what thread is attached to what point and make the wires loose with pliers. Be careful not to squeeze the connection.

5.   Loosen the screws in the watertank – put the rubber rings in a safe place, not to lose them. Sometimes they are stuck to the water tank.

6.   Pull the water tank right up from the machine by pulling the tube in the middle. All cables that are attached, come along.

7.   Gently pull off the glass tube, hold the water tank with one hand so it does not "jump" when the tube comes out.

8.   Remove the rubber adapter in which the glass tube is inserted (perhaps use soapy water).

Mounting

1.   Place the new rubber adaptor on the nozzle of the water tank.

2.   Push the glass tube well in the rubber adaptor, the top should come all the way to the top of the rubber adapter, there should be no space in the adapter left. If needed use a hard object (e.g., a book) to press the glass tube in the adaptor but be careful not to break it.

3.   Put this complete set in the machine.

4.   Glass tube gently and straight through the hole in the metal bracket. No bumping or pushing!

5.   Put the screws in the water tank (note the black rubber rings).

6.   Turn the machine and attach the wires to the micro-switch (sliding).

7.   Push the black rubber tube as far as possible on the copper pipe.

8.   Put the screws in the bottom plate.

Did you order the wrong part? You can return unused articles within 14 days after receipt (own expense).

Moccamaster 2018 - Handbuilt by professionals